The water heater can't catch fire, the water heater can't catch fire.

When using a water heater, sometimes it will not catch fire. So what is the reason why the water heater can't catch fire ? What is the corresponding solution? The decoration home decoration network Xiaobian to introduce one by one.

Cause 1, power problem :

Solution: Check if the AC power plug indicator is on, first remove the problem from the power supply.

Cause 2, solenoid valve failure :

Solution: If you only hear the ignition sound when the ignition, there is no electromagnetic valve "å—’" magnetic sound, it may be damaged or aging of the solenoid valve, the solenoid valve is aging, it will be uncontrolled, it can be sucked at the beginning of the fire, It catches fire, but then closes and turns off the flame; it may also be too high or too low gas pressure. The water heater using the cylinder gas will have too high or too low output pressure of the cylinder pressure reducing valve. The water heater can't be fired; it is more likely to be electromagnetic The valve is dirty. The solenoid valve can't be over-gas, and the gas (natural gas, liquefied petroleum gas, artificial gas) can't come out, can't come out, so it doesn't catch fire. Before confirming that the solenoid valve is good or bad, make sure that the igniter control circuit is normal. If there is a fault, the solenoid valve cannot be controlled.

Reason 3, electric igniter failure :

Solution: One of the pulse igniter and the controller is faulty, and the water heater cannot ignite.

Reason 4: Ignition porcelain needle or induction porcelain needle problem :

Solution: a. Ignition needle is very difficult to ignite when aging or aging. It can be replaced or the ignition needle can be placed correctly. b. Induction aging, the induction can be polished and placed (so that the flame can fully burn the fire regardless of the fire or the small fire) Needle).

Reason 5, water pressure problem :

Solution: a. The water heater can not start normally when the water pressure is low; b. The water filter can not flow normally after the water inlet is blocked, and it can be cleaned up.

Reason 6, water and gas linkage failure :

Solution: a. The tympanic membrane aging or damage in the water-gas linkage valve can not push the micro switch; b. the micro switch is broken.

Cause 7, the air supply switch is not open or the air filter is blocked :

Solution: Turn on the air supply and clean the air intake filter.

Reason 8, the gas does not match :

Solution: For example, the liquefied gas water heater is connected to the natural gas, etc. In this case, the liquefied gas water heater needs to be changed to natural gas before it can be used.

Reason 9, the valve seal is eroded by the gas :

Solution: Replace the parts.

Reason 10 : The pipe cannot be properly vented :

Solution: a. The pipe is blocked, and the pipe is blocked; b. The pipe is too long and is not installed correctly.

Reason 11, the problem of poor contact of the air-cooled hot water switch :

Solution: Connect the hot and cold water switch.

Cause 12: The ignition switch resistance value becomes large or the contact problem is poor :

Solution: a. If the resistance of the ignition switch becomes larger, the amount of electricity flowing into the battery will decrease, and the current will become smaller. The magnetic attraction is naturally small, so the magnetic attraction cannot be turned on, resulting in failure to catch fire. In this case, it is necessary to slightly adjust the resistance of the ignition switch in the water heater. b. If the ignition switch is in poor contact, it is necessary to ensure that the ignition and the switch are normal.

Through the above introduction, we must have some understanding of the reasons why the water heater does not catch fire, and at the same time master some corresponding solutions. If you want to know more about the reasons why the water heater does not catch fire, please continue to pay attention to the decoration home network.

More related wonderful reading:

Natural gas water heater can not catch fire and repair methods

What if the water heater can't catch fire? The reason why the water heater can't catch fire

Why can't gas water heaters catch fire? Avoid no hot water

What if the gas water heater can't catch fire? PK electric water heater

Ageless Skin Rejuvenation

Facial rejuvenation treatments are one of the best ways to invest in the health of your skin. Treatments provide both prevention against the factors affecting aging as well as treatment for fine lines, wrinkles, pigment, redness, volume loss, and laxity.

Reborn PLLA Dermal Filler and Reborn PLLA Hydrogel are Facial fillers, very good for Ageless Skin Rejuvenation.

Reborn PLLA Dermal Filler is a Collagen Stimulator, a new injectable treatment to smooth wrinkles, restore facial volume and contour the face. It works by stimulating the rebuilding of the body`s own collagen to get rid of lines and wrinkles and restore a youthful appearance with gradual, natural looking results.

Suitable for face (except the red area in the lip and the area in nose),neck,hand,breast,genital,stretch marks,and buttock.Especially Reborn plla is very suitable for thin area, such as under eye, forehead, lacrimal groove..

Reborn PLLA Hydrogel is for mesotherpay. Mainly for fine wrinkles and facial texture improvement.

Ageless Skin Rejuvenation,Cheek Volume Filler,Cheek Lines Filler,Hyaluronic Acid Injection Face,Cheek Filler To Slim Face

Rimless Industry Co.,Ltd. , https://www.rimlessmedbeauty.com