Matters needing attention in powder packaging machine

Matters needing attention in powder packaging machine

The powder automatic packaging machine is one of the packaging machines. It can pack powders with low viscosity, such as milk powder, cereal, coffee, etc., which can achieve the ideal packaging effect. After the manufacturer purchases the powder automatic packaging machine, it often has some doubts in use. The specific operation process of the product and the matters needing attention in it are not clear. Then the technical personnel of the company will talk about the powder automatic packaging machine. Instructions and some precautions.

The first part is the filling part. Before packaging, the material to be packed must be loaded into the hopper of the automatic powder packaging machine. This process is generally done from the following aspects:
1. Start stirring at the same time of loading, which can make the material evenly distributed in the hopper and avoid uneven packaging;
2. Set the proper number of feeding bags according to the characteristics of packaging materials and packaging specifications to ensure stable feeding and reduce the weight change caused by the impact of feeding to affect the accuracy of measurement;
3. If you hear an abnormal sound from the silo during work, stop the machine immediately and check the status of the silo to ensure that there are no foreign objects before you can continue to work;
4. When packing small specifications , do not place the weighing platform in a place where the air flow passes large, because the wind can affect the minimum division display of the sensor, the balance is sensitive to the force of the wind, causing the measurement display to be unstable.

After the filling process is completed, it is the packaging of the material. This is an important part of the packaging work, and it needs to be divided into several steps:
1. Set the parameters of each part according to the instruction manual of the equipment to ensure the accuracy of the packaging after the start of the work. You can first try the machine once and let the screw in the cup be filled with material;
2. During the packaging work, the operation of the automatic powder packaging machine must be standardized. Do not let the material in the cup and the material in the packaging bag squeeze each other when receiving the material, otherwise it will be easy to change due to the adhesion of the material. It causes dripping or so-called leakage, which causes inaccurate measurement or large measurement fluctuation;
3. During the packaging operation of the powder automatic packaging machine, if the material is received many times or partially missed, do not put it on the weighing platform, otherwise the computer will consider the exact data of its one-time feeding and will adjust it, affecting the subsequent Continuous working accuracy and speed;
4. When there are foreign objects at the mouth of the cup during the work, stop and take out. Note: Do not take foreign objects by hand before shutting down, so as to avoid injury to the body due to the rotation of the photoelectric screw
5. When replacing and cleaning the screw of the cup, avoid swinging the screw horizontally to avoid distorting the screw slot, which will affect the abrasion of the screw after the screw is fixed and will increase the accuracy of measurement. When it is difficult to remove, you can loosen the long shaft and take it out again, then take out the screw. After finishing, repair the card slot and internal foreign objects or materials;
6. Do not cover heavy objects or sit on the sensor table . The maximum load capacity should not be greater than the maximum weighing range, and the sensor should be placed away from large vibration sources;
7. When replacing and adjusting the tensioner , the automatic powder packaging machine should pay attention to its installation direction and the up and down position of the two thick and thin gaskets. The narrow side of the fixed pad of the tensioner is inward. Adjust the position of the moving sprocket to adjust and install the powder automatic packaging machine in time.

Finally, it is the post-packaging work, generally finishing and cleaning work to ensure that the equipment is clean and easy to use next time:
1. After the packaging work is finished, unload the materials in the silo and clean the screw cups to avoid the agglomeration of the remaining materials due to the unclear materials in the next work (due to the characteristics of the chemical materials that are easy to absorb moisture). , Affecting the packaging accuracy;
2. Keep the photoelectric switch electric head clean, so as to prevent the photoelectric action from being insensitive due to the adhesion of dust, causing the wrong cutting or non-action, affecting its life. Note: use a hard brush to clean the photoelectric sensor head;
3. Before leaving the machine, the personnel can leave after turning off the power of the machine to ensure that the machine has intermittent work and heat dissipation, to avoid continuous temperature rise caused by continuous work, to aggravate equipment wear and reduce the service life of the whole machine and parts.

For mechanical equipment such as powder automatic packaging machine , in normal use, as long as it can achieve standard operation, and regular maintenance and maintenance, it can ensure the good use of the equipment, and can pack the desired effect, but also increase The service life of the equipment. Never arbitrarily repair and disassemble the machine to avoid unnecessary damage.

If you do n’t understand anything, you can consult the 24- hour phone: 13838093755. All colleagues of Dongfang Rising Sun Packaging Equipment in Zhengzhou will provide thoughtful and timely service .